Description
Back in stock as of December 13, 2024
Short adjustable plug available with new barrel order.
Custom laser engraving available on barrels by request for an additional charge
For barrels equipped with the short adjustable plug please see directions here
As of the second week of August 2024 I have gone back to the old marking due to customer feedback;
0=zero gas
1=.040
2=.0469
3.052
4=.0525
This adjusts with a simple turn of the plug. With either an allen wrench or adjustable/box wrench. When the number is at the 12:00 position that is the port size it is on
Different setups require different amounts of gas depending on the actual gun itself, spring rate, suppressor generated back pressure and ammunition. This plug allows you the ability to “tune” your setup with the last amount of gas necessary to function, reducing gas feedback to the shooter. Your best method for tuning is to start on the largest port working backwards until the gun does not function then go up one click. You may need to adjust to more gas as the gun gets dirtier through the cycle.There is no one setting I can suggest for your setup with all the variables, it will require some testing by the end user. The plug insert is a consumable part and will erode over time as it is subjected to the hot chamber gasses which act as a type of plasma cutter. It will try to match the size of the port to the plug and erode the steel. this slows and still works as a funnel until eventually working all the way through. Erosion depends heavily on ammunition choice and suppression back pressure. There is not an alloy that I can machine that will prevent this/strong>
Gen-2 MPX-type replacement Drop-in Barrel & Gas Block assembly:
Barrels are available in 4″, 4.5″,5.25″, 5 5/8″, 6.5″ and 8″ lengths ( Carbine barrels are available separately under their own tab in mpx parts), with 1/2-28 concentric threads for suppressor use. Thread protector is included.
You can also add a 1-piece HK-type 3-lug, machined directly onto most barrel.
All barrels 8″ and shorter are default shipped with .0625 gas port, longer barrels are shipped with .055 ports. All tri lug barrels also have 1/2-28 threads on the end and include thread protector. There is now an option for tri lug without threads
-1:10 Riffling
-.438 Threaded muzzle on both tpi only and tri lug with tpi
-nitride finish
If you have questions or wish to share information and have Facebook you can join this group HERE
I do not accept returns on barrels due to liability and cannot sell them as new once they are shipped out and returned. If there is a function issue obviously I will make that right if it is due to my product. Please, please, please make sure the barrel length and configuration is the proper one for your platform. I want people to be happy with their purchase and get the proper barrel for their platform in the length that is best suited to their purpose. If unsure please contact me first and I can possibly help with identification and input.
There is no additional cost for shipping it is included in the price of all listed parts. Insurance is optional and separate, there is a box at the bottom of the checkout page where you can accept or opt out of the insurance. ILWT cannot be responsible for lost or mishandled shipments once they are dropped to USPS. If you checkout without requesting insurance your item will be sent with only the amount afforded by USPS for your particular shipment which may not be anything for small items and up to $100.00 for some priority packages. Insurance will not let me file a claim if it is showing delivered so please make sure you put in the proper address or desire signature confirmation for an extra fee. By placing the order you acknowledge and accept this.
Please use drop-down menu for barrel length and 3-lug option, when ordering.
We use the tightest of tolerances and highest quality control.
All barrels and gas-blocks are proudly made in the USA and engraved ILWT.
All NFA Rules apply
*As with any barrel swap, have a qualified gunsmith check head-spacing before firing.
DISCLAIMER: “MPX” is a federally registered trademark of SIG SAUER, Inc. and is one of many trademarks owned by SIG SAUER, Inc.
Neither ILWT, LLC nor this website are affiliated in any manner with, or otherwise endorsed by, SIG SAUER, Inc.
The use of “MPX” on this page is merely to advertise the sale of MPX type barrels, parts, or components.
<>
Additional information
| Weight | 14 oz |
|---|---|
| Configuration | 4.5" Tri Lug No Threads, 4.5" Tri Lug no threads with adj plug, 5 5/8" Tri Lug No Threads, 5 5/8" Tri Lug No threads with adj plug, 6.5" Tri Lug No Threads, 4" tri lug with 1/2-28 threads, 4" tri lug with adjustable plug, 4.5" 1/2-28 tpi only, 4.5" 1/2-28 only w/adjustable gas plug, 4.5" tri lug with 1/2-28 tpi, 4.5" Tri Lug with 1/2-28 Threads w/adjustable gas plug, 5.25" 1/2-28 tpi only, 5.25" 1/2-28 TPI with adj plug, 5 5/8" Tri Lug with 1/2-28 Threads, 5 5/8" Tri lug with 1/2-28 Threads w/adjustable gas plug, 5.25" 1/2-28 tpi only, 5.25" 1/2-28 Threads w/adjustable gas plug, 5.25" Tri Lug Only Open Plug, 5.25" Tri Lug Only with adjustable plug, 5.25" Tri Lug with 1/2-28 threads and open plug, 5.25" Tri Lug with 1/2-28 threads with adjustable plug, 6.5" 1/2-28 tpi only, 6.5" 1/2-28 threads w/adjustable gas plug, 6.5" tri lug with 1/2-28 tpi, 6.5" Tri lug with 1/2-28 threads w/adjustable gas plug, 6.5 13.5 x 1 LH TPI Only, 6.5 13.5 x 1 lh tpi w/adjustable gas plug, 8" 1/2-28 tpi only, 8" 1/2-28 threads w/adjustable gas plug, 8" tri lug with 1/2-28 tpi, 8" tri lug with 1/2-28 threads w/adjustable gas plug, 10" 1/2-28 threads, 10" 1/2-28 threads w/adjustable gas plug, Add Ion Bond |
13 reviews for Gen-2/3 ILWT MPX-type PISTOL Barrels w/Gasblock assembly
Only logged in customers who have purchased this product may leave a review.
Returns and Exchanges
There are a few important things to keep in mind when returning a product you purchased.You can return unwanted items by post within 7 working days of receipt of your goods.Barrels may only be returned if they are unused and marked as returnable in description due to insurance and liability restrictions. If used or labelled as non returnable then repair/replacement only apply for function issues. .
- Only items that have been produced by us.Items manufactured by others will need to be addressed by the manufacturer
- Please ensure that the item you are returning is repackaged with all elements.
Ship your item back to Us
Contact us for returns and information prior to shipping.Related Products
left
right
Both 6.3″ 1/2-28 tpi and 7.4″ Tri Lug with 1/2-28 tpi back in stock and shipping as of 05/13/2024 The 7.4″ fit the full size...
$200.00 – $250.00
Select options
This product has multiple variants. The options may be chosen on the product page
left
right
Back in stock and shipping as of 01/19/2024 ILWT Has procured some factory bolt carrier assemblies from Sig Sauer. These are oem and will work...
$600.00
Add to cart
We were asked to bring this back so we obliged. This block is very helpful when removing the barrel retaining and detent pins. This locks...
$60.00 – $75.00
Select options
This product has multiple variants. The options may be chosen on the product page
Non-Threaded direct replacement barrel for The Classic Colt 1903 .32 Pocket Hammerless Model M (Bushing model). 4140 heat-treated steel. Available in Blued finish. Perfect to...
$210.00
Add to cart
Add Ion Bond to the barrel extension of any MPX barrel order. The slick, low-friction DLC coating gives firearms extra dry lubrication properties for moving...
$40.00
Add to cart
An exclusive ILWT Item! For all gen MPX guns and models. This pin does not require one to use alignment dots, if the firing pin...
$38.00
Add to cart
left
right
These are NOT Chambered in 9mm they are chambered in 22tcm9r. Please read about the cartridge before ordering. Gen-2/3 MPX-type Drop-in Barrel & Gas Block...
$500.00
Select options
This product has multiple variants. The options may be chosen on the product page
left
right
Limited stock, one per order PLEASE! ILWT Has procured some factory extractors from Sig Sauer. These are oem and will work in all Gen II/III,...
$27.00
Select options
This product has multiple variants. The options may be chosen on the product page
Proper torx screws for the Older MPX Ejector. These are often buggered or broken during removal.Nice to have as spares. Three in each package. These...
$10.00 – $15.00
Select options
This product has multiple variants. The options may be chosen on the product page
These barrels are out of stock as of 12/26/2024 and I do not have any immediate plans to produce more. Sorry Non-Threaded direct replacement barrel...
$125.00
Read more
left
right
Replacement or spare hardened and black oxide barrel retaining nuts for the Stribog. These will fit all models but have the larger slots of the...
$15.00
Select options
This product has multiple variants. The options may be chosen on the product page
left
right
Back in stock as of December 13, 2024 Add a Factory Sig MPX PCC 16″ hand guard for an extra $50.00 while supplies last with...
$40.00 – $695.00
Select options
This product has multiple variants. The options may be chosen on the product page
M11/9 9MM Tri Lug Barrels with 1/2-28 TPI Threads and wrench flats for easy installation. There is no additional cost for shipping it is included...
$215.00
Select options
This product has multiple variants. The options may be chosen on the product page
left
right
Replacement inserts for the short plug with the 5 settings now available as standalone parts and will utilize the existing sleeve and nut from your...
$10.00 – $110.00
Select options
This product has multiple variants. The options may be chosen on the product page
left
right
charles.murphy3
I ordered the 8″ Gen 2/3 ILWT MPX barrel in August. I finally got around to using it (due to ammo shortage) on Saturday, and it was outstanding. I swapped out a 4.5″ MPX barrel for the 8″, and the ILWT barrel was lighter and my groupings were incredible. I highly recommend this product for anybody looking to replace, upgrade or change their barrel lengths on an MPX. It is considerably less expensive than the Sig manufactured barrels and the quality is absolutely outstanding. Also, the 1/2-28 thread pitch is great if you are looking to add a muzzle device because 13.5-1 LH is sometimes difficult to find. Also, Rob’s customer service was exceptional. Bottom line – great product and great service! Thank you, ILWT.
Best regards,
CM
thlacymd
I purchased the 4.5 inch barrel with 3 lug mount and restricted plugs for gen 3 MPX. With stock barrel, stock plug, 3 lug adaptor and an old SWR trident accuracy was abysmal. It was also doubling occasionally. I did’t shoot it unsuppressed but other hosts shot well with the same can and suppressor alignment with adaptor was good. Stock barrel may have been crap or perhaps it was overgassed and unlocking early. With the ILWT barrel and .0469 plug it will shoot about an inch at 25 yards which is a vast improvement. This is with a cheap red dot and minimal load testing. Reliability so far is 100% but I haven’t shot it a whole lot yet. Doubling has also stopped. Fit and finish is excellent. Rob is also very responsive to questions which is quite refreshing.
THL
Brian Malek
Purchased the 4.5″ Threaded barrel for my MPX Copperhead, Putting around 300 rounds through it this weekend and it runs flawlessly, Accuracy seems just as good as the original barrel, Zeroed at 25 Yards and getting 2 inch groups Rob has amazing customer service and has earned a lifetime customer.
Joseph Bender
I bought the Sig MPX K with the intention of shooting it suppressed. I started with a Griffen 3 lug adapter and quickly found out the accuracy was terrible. It was shooting 9-10 inch groups at 25 yards with Rugged Obsidian installed. I did some research and found the inleadwetrust barrel. I ended up getting the 4.5 inch with Tri Lug-1/2×28 with adjustable gas block. My 9-10 inch groups shrunk down to 1.5-2 inch groups at 25 yard. The adjustable gas block made shooting suppressed very enjoyable. I would recommend if you ever plan on shooting suppressed to pay the extra cash for adjustable gas block. Lastly Rob answered all my dumb question with no hesitation. Great Company
manny85382
I had one of the defective MPX barrels and could get any consistent groupings. I contacted Rob and he helped me pick out a barrel and that totally fixed the issue. I was getting consistent groups and the gun was shooting great. I highly recommend this barrel if you have a defective MPX barrel!
manny85382
I had one of the defective MPX barrels and could get any consistent groupings. I contacted Rob and he helped me pick out a barrel and that totally fixed the issue. I was getting consistent groups and the gun was shooting great. I highly recommend this barrel if you have a defective MPX barrel!
jmdxrated
I bought the 6.5 inch and was not disappointed. The quality was better than sig quality. I went from thinking about selling my mpx k to now enjoying it and not wanting to sell it. The accuracy was much better, even with attachments. Thank you Rob.
Jeff Ferguson
I have a MPX-K (latest generation) with the 4.5″ barrel using the SiCo ASR mount system with a SiCo 36M. The grouping was not the best. If I took the suppressor off, the grouping was a little better, but not what I would expect from a Sig, I purchased the ILWT 4.5″ tri-lug with adjustable gas block and what a difference this barrel system makes! Very little point of impact change, but shot groups are very good. I was so happy with this arrangement that I then purchased the 4″ tri-lug with adj gas for my MPX FDE Copperhead. This is the barrel that Sig should be putting on this gun! With the SiCo 36M attached, the groups are very tight and on this one there was NO point of impact change when attaching the suppressor! This gun went from one of my “not so fun to shoot” to one of my favorites! Rob is great to work with, the best customer service I have seen!
Glen Sakai
MPX-K Gen 3 (mid 2022 model)
6.5 trilug threaded standard gas plug
Dropped it in and resighted my dot. Hit a 4 inch gong at 50 yards without much effort and just resting on a couple of stacked 4×4’s. Could probably do better but its a pcc not a long range precision gun so thats good for me. Now just waiting on my longer hand guard to go over my suppressor (omega 36m). No regrets buying the 6.5inch, perfect length for velocity but not being too long once suppressed
js.christensen
I have an early MPX Gen 2. The factory 8” barrel was ok. From a rest I would get 2-3 inch groups at best, my AR9 shoots sub 1 inch groups from the same setup. I hand load my ammo and I could not get the accuracy any better. Adding a suppressor the accuracy remained the same but I would get weird POI shifts, probably barrel harmonics but it was different every time. Tried three different 3 lug adapters, no change. I finally decided to try the 8 inch 3 lug ILWT without the adjustable gas plug. This barrel prints consistent groups 1 inch or less, plus it is much less gassy than the factory. Just wish I would have done it sooner.
Karl Bolle
Due to my absolute obsession with my MCX I took a risk and got a decent deal on a 2nd gen MPX recently. Had horrible accuracy issues with the 4.5 inch stock barrel. tried three different tri-lugs and the moment any of them were installed went everywhere. Accuracy wasn’t so good with a raw barrel either. Sent to Sig for an accuracy test, they replaced both the barrel and the bolt for free + shipping (good on them) but again, the moment a tri-lug went on, accuracy went to hell.
Got a 6.5 ILWT barrel with tri-lug and adjustable gas. Instant 1 inch groups at 25 from a bag. Popping on a suppressor (Omega 36m) opened things up a bit, but since it was on a bag that could have been me. Best part, the 6.5 is about as long as the 4.5 with a tri-lug added. Stinks to invest even more into an expensive gun, but ILWT really nailed it. Great job. Went from a gun I was ready to flip to a gun I’m thinking I’ll SBR and keep forever.
Also, Rob’s customer service is amazing. He is shockingly responsive and engaged with his customers. I’m a happy customer.
Sean Eady
I’m not big on words, so short and sweet. Quality and customer service are second to none. Very pleased with this barrel. Fit, finish and accuracy is incredible !!!! Outstanding product.
chuckcarternc
Purchased the 6.5″ barrel with adjustable gas block for my Sig MPX K. Was just so frustrated with the factory 4.5″ barrel when shooting suppressed. Inconsistent accuracy and too much gas in the face. Tried with Sig SRD9, Octane 9, and Omega 36M but nothing was satisfactory. The Omega 36M was quietest and less gas but because you cannot get a 13.5 x 1 LH mount, you have to use the ASR mount. That just made accuracy issue worst. Only using Federal American Eagle 147gr. The ILWT barrel was amazing. right out of the box shooting groups at 25 yards which I could cover with a quarter. My only regret is I did not upgrade this sooner as I could have saved then several hundred rounds trying to fix the Sig barrel issues. I went with the 6.5″ over the 8″ inch barrel as it fits perfectly in a small back pack. Rob is awesome when it comes to helping you out with a problem. Excellent service, excellent product.
tkreuchi
After reading on the internet how great the In Lead We Trust Barrels are I decided to order the 4 1/2-in with the Tri Lug and Adjustable Gas Plug for my MPX Copperhead I wanted to run my SilencerCo Octane 9 with the Tri Lug and to avoid using an adaptor on the end of the barrel. But because I was in a hurry I never measured anything and sure as hell the Tri lug adapter from SilencerCo does not clear the hand guard on the Copperhead K so I purchased the 5 5/8-in barrel with the Tri Lug and the Adjustable Gas Plug and since I had a nice 4 and 1/2-in barrel laying around I went ahead and bought an MPX K. That is how good these barrels are that you will buy a new gun just to have a host for the barrel. The accuracy is the same if not better than the stock barrel. Where the ILWT Barrels shine is when shooting suppressed both in accuracy and gas control they are so much better than the stock barrel with the can attached either Tri Lug or Direct Thread. If you’re hesitant at all about getting this barrel I recommend go ahead and pull the trigger (Pun intended) In all of my ramblings I have not mentioned the outstanding customer service Rob is a great guy very responsive to emails and calls he even answers questions on the Face Book. They make shooting your MPX fun to shoot. That’s the best complement I can give.
David Calhoun
Like everyone else who came here, I was having issues with the factory 4.5in barrel after I attached a tri-lug device and put a suppressor on it. I was getting inconsistent groupings and was quite irritated as I planned on only shooting the weapon suppressed. This has been my dream gun and so to finally get it and not enjoy shooting it was pretty disheartening. After months of research I kept seeing ILWT come up so I did more digging. Not only was everyone getting great results, but they mentioned how helpful Rob had been for the community. I finally bit the bullet and ordered an 8in barrel with the new adjustable gas plug and wow, what a difference. Took it out and I was immediately getting 1in groups at 25 and 50 yards. Substantially less gas after tuning it as well. One of the things I love most about firearms is the community and how passionate people are. It felt really good giving my money to another hard working American who has poured his passion into making a really great product. Don’t hesitate to pick up one of these barrels, they really are the best.